Coach Bolts Explained: How to Choose the Right Size, Length and Finish

To choose the right coach bolt, match three things: the thread size (M6 to M12 for most timber jobs), a length that clears your timber plus a washer and nut with a couple of threads to spare, and a finish that suits where it will live. Bright zinc plated (BZP) steel is for indoor and dry use. A2 stainless suits sheltered outdoor use. A4 (316) marine grade stainless is the one for coastal and harsh conditions.

That is the short version. Below is how to work it out for your own job, with the sizes to check against.

In this article

What is a coach bolt?

A coach bolt has a domed head and a square section under it, called the neck. You drill a hole, tap the bolt through, and the square neck pulls into the timber. That stops the bolt turning, so you can tighten the nut from the other side with a single spanner. The domed head also has no drive to grip, which makes it harder to undo from the outside.

In UK use, "coach bolt" and "carriage bolt" mean the same fixing. The standard most are made to is DIN 603. Do not confuse them with coach screws, which have a hex head and thread straight into the timber. The two are not interchangeable, and a coach screw needs no nut.

Coach bolts are typically used to fix timber to timber or timber to metal: gates, fencing, timber frames and general carpentry. The domed head resists pulling through the wood, and the square neck holds it in place.

What size coach bolt do I need?

Most timber work sits between M6 and M12. The number is the thread diameter in millimetres, so an M10 has a 10mm thread. Heavier loads and thicker timber call for a bigger diameter. For gates, frames and anything that carries weight, M10 and M12 are the usual starting points.

Nominal DIN 603 dimensions for the sizes we stock most (all in mm, nominal):

Size Thread pitch Head diameter Length range
M6 1.0 16 16 to 150
M8 1.25 20 20 to 150
M10 1.5 24 20 to 200
M12 1.75 30 30 to 200

The head diameter matters more than people expect. A bigger head spreads the load over more timber, which is why M12 coach bolts are a sensible choice for gates and larger frames.

How do I work out the right length?

Coach bolt length is measured from under the head to the tip, so the square neck counts towards it. Add up four things:

  1. The total thickness of everything you are clamping.
  2. The thickness of the washer.
  3. The height of the nut (roughly 8mm for M10 and 10mm for M12).
  4. A couple of threads showing beyond the nut.

Worked example: two 38mm timbers make 76mm. Add about 2mm for the washer, about 8mm for an M10 nut and a few millimetres of thread, and you land at around 90mm. The next size up is an M10 x 100mm, which is the one to buy.

If you are between two lengths, go to the longer one. A bolt that is a little long is fine. One that only just reaches the nut is not.

M10 x 100mm zinc plated coach bolts with nuts and washers
For indoor and dry timber work
M10 x 100mm Coach Bolts, Zinc Plated, DIN 603

Grade 4.8 steel, each supplied with a full nut and Form A washer. Packs of 4, 10 or 25.

Zinc, A2 or A4: which finish should I choose?

The finish decides how long the bolt lasts, and it is where most mistakes happen. Choose by where the bolt will sit, not by price alone.

Finish Best for Avoid it for
Bright zinc plated (BZP) Indoor and dry use, general carpentry Prolonged outdoor or wet exposure
A2 stainless Indoor and sheltered outdoor use Marine or saltwater immersion
A4 (316) marine grade stainless Salt water, coastal and harsh conditions Nothing, but it costs more than zinc or A2

Zinc plating is a light finish. It does the job inside a dry building and is the cheapest option, but it is not made for rain. A2 stainless gives good corrosion resistance for sheltered spots. If the bolt is near the sea, A4 316 is the stainless grade used for salt water and coastal environments, and it is the one to pay for.

One honest note on strength: stainless bolts are chosen for corrosion resistance, not as a replacement for high tensile bolts. If a joint carries a serious load, check the strength requirement first, then pick the finish.

M12 x 150mm A2 stainless steel coach bolts with nuts and washers
For sheltered outdoor use
M12 x 150mm Coach Bolts, A2 Stainless Steel, DIN 603

Pack of 4 with matching A2 stainless nuts and Form A washers.

M12 x 150mm A4 316 marine grade stainless coach bolts pack of 8
For coastal or harsh conditions
M12 x 150mm Coach Bolts, A4 316 Marine Grade, DIN 603

Pack of 8 with matching stainless nuts and Form A washers.

How do I fit a coach bolt?

  1. Drill the hole. Coach bolts need a pre-drilled hole through the timber (coach screws are the self-tapping ones). Drill straight, at the same diameter as the thread, so the bolt slides in with light taps.
  2. Tap the bolt through. Use a mallet or hammer on the domed head until the square neck seats into the face of the timber.
  3. Add the washer and nut. Put the washer under the nut, on the side you tighten. It spreads the load and protects the surface.
  4. Tighten with one spanner. The square neck holds the bolt still, so you only need to turn the nut. Stop when the joint is firm. Over-tightening can crush the timber.

The most common mistakes are a bolt that is too short, a hole that is too large (so the square neck has nothing to grip), and zinc used where it will be rained on. The first needs a length check, the second a drill bit that matches the thread, and the third a switch to stainless.

M12 x 150mm zinc plated part threaded coach bolts pack of 4
For heavier indoor timber work
M12 x 150mm Coach Bolts, Zinc Plated, Part Threaded, DIN 603

Pack of 4, each with a full nut and Form A washer.

Frequently asked questions

Is a coach bolt the same as a carriage bolt?

In UK use, yes. Both names describe a domed head bolt with a square neck, usually made to DIN 603, and both are fitted with a nut and washer.

What is the difference between a coach bolt and a coach screw?

A coach bolt goes right through the material and is fastened with a nut. A coach screw has a hex head and threads into the timber, so it needs no nut. They cannot be swapped for each other.

Do coach bolts need a washer?

Yes, fit a washer under the nut. It spreads the clamping load and stops the nut digging into the timber. Our packs include a full nut and a Form A washer with each bolt.

Can I use zinc plated coach bolts outside?

BZP is a light finish for indoor and dry use. For outdoor jobs choose A2 stainless in sheltered spots, or A4 (316) marine grade near the coast.

How long should a coach bolt be?

Add the thickness of your timbers, the washer and the nut, then allow a couple of threads beyond the nut. If you land between sizes, take the longer one.

Ready to choose your coach bolts?

Every pack comes with nuts and washers, in zinc, A2 and A4 marine grade.

Shop fasteners →

Dimensions are nominal. Always choose a grade and finish that suits your application. For background reading, see the RS Components coach bolts guide.