A missing grub screw can stop a pulley, collar, handwheel or machine guard from being put back into service. The part may be small, but ordering the wrong thread or point type can create lost time, damaged mating parts and an insecure repair. Knowing how to identify grub screw sizes means checking more than the diameter visible at the hole.
Grub screws, also called set screws, are headless threaded fasteners designed to sit flush with, or below, the surface of the component. They are commonly tightened with a hex key, although slotted and other drive types are also used. Their job is usually to lock one component onto another, such as securing a gear to a shaft or a handle to a spindle.
Start with the thread diameter
The thread diameter is the first size to establish. For a metric grub screw, this is stated as an M size, such as M4, M5, M6 or M8. It refers to the nominal outside diameter of the thread, not the diameter of the drilled hole in the component.
Use vernier callipers to measure across the highest points of the external thread. Take the measurement on a clean, undamaged section rather than at the first thread or the point. A reading close to 6 mm normally indicates an M6 screw, while a reading close to 8 mm indicates M8.
Do not rely solely on a ruler. A difference of 1 mm between common fastener sizes is easy to miss, and a near match may still start in a threaded hole before binding or cross-threading. If the original screw is unavailable, measure the internal thread with a thread plug gauge where possible, or test a known-good bolt of the suspected size by hand. It should screw in freely for several turns without force.
Metric thread diameter guide
The most frequently encountered metric sizes in general workshop and maintenance work are M3, M4, M5, M6, M8, M10 and M12. Smaller sizes are often found on controls, instrumentation and light assemblies. Larger sizes are more typical on substantial shafts, fixtures, tooling and machine components.
A grub screw marked M6 has a nominal thread diameter of 6 mm. It does not mean the hex key size is 6 mm, and it does not describe its length. These details must be identified separately.
Check the thread pitch before ordering
Two grub screws can have the same nominal diameter but different pitches. Thread pitch is the distance from one thread crest to the next, measured in millimetres. Standard coarse pitch is the normal choice for most metric grub screws, but fine pitches are used where higher adjustment resolution, thinner-wall components or existing machine threads require them.
For example, common coarse metric pitches include M5 x 0.8, M6 x 1.0, M8 x 1.25 and M10 x 1.5. An M8 x 1.0 fine-thread screw will not fit an M8 x 1.25 hole, despite both having an 8 mm outside diameter.
A thread pitch gauge gives the most dependable result. Hold the gauge leaves against the thread until one profile sits fully in the grooves with no visible gap. If a gauge is not available, measure the length occupied by several complete threads using callipers, then divide by the number of thread spaces. Measuring over ten thread spaces is more reliable than trying to judge a single pitch.
Be alert to imperial threads on older machinery, imported equipment and legacy repairs. UNC, UNF, Whitworth and BA threads can look close to metric sizes but are not interchangeable. Their pitch is normally specified as threads per inch rather than millimetres. If an apparently metric screw feels tight almost immediately, stop before the thread is damaged and verify the standard.
Measure grub screw length from end to end
Because a grub screw has no head, its stated length is usually the overall length from one end to the other. Place the screw between the jaws of callipers and measure from the drive end to the tip or point. Record the length in millimetres alongside the thread size, for example M6 x 12 mm.
Length matters because the screw needs sufficient thread engagement in the tapped component while reaching the shaft, flat or locating feature it is intended to secure. A screw that is too short may not contact the mating part properly. One that is too long can protrude into a bore, foul a moving component or bottom out before applying clamping force.
Where the original screw has sheared off or is missing, measure the threaded depth of the hole with a depth gauge, drill shank or suitable probe. Allow for the required contact position and avoid selecting a length that reaches the bottom of a blind hole. In a through-hole, check both sides for clearance and whether a flush finish is required.
Identify the point type, not just the size
The point style determines how the grub screw grips the mating part. This is often as important as the thread and length. A cup point is one of the most common options. Its concave end bites into a shaft or surface and is suitable for permanent or semi-permanent fixing where minor marking is acceptable.
A flat point spreads load over a wider area and is less likely to damage the mating surface. It is often used against a flat machined onto a shaft or where frequent adjustment is expected. A cone point gives concentrated contact and positive location in a matching recess, but it can mark softer materials.
Dog point grub screws have a short, unthreaded cylindrical projection at the end. The dog locates into a hole, groove or slot, making them useful where repeatable positioning is needed. It is essential to include dog length in the specification, as an otherwise correct thread and overall length may still fail to locate correctly.
Common point descriptions include:
- cup point
- flat point
- cone point
- dog point
- knurled cup point
Confirm the drive size and condition
Most modern grub screws use an internal hex socket. The hex key size is not the screw size, but it is useful for confirming what you have and for planning installation. An M6 grub screw may use a 3 mm hex key, while other thread sizes use different key sizes depending on the applicable standard and screw series.
Check the socket for rounding, corrosion or packed debris before removal. Clean it with a pick or compressed air, then seat a good-quality hex key fully. A poor-fitting key can round the socket, particularly on hardened screws that have been tightened with threadlocking compound.
If a replacement is being specified for a repair rather than matched to an existing screw, consider access. A standard internal hex drive is compact and widely used, but a slotted grub screw may suit a shallow application or equipment designed for screwdriver adjustment. The drive must be practical to tighten in its installed position.
Consider material, finish and operating conditions
A correct dimensional specification is only part of the requirement. In dry indoor machinery, blackened alloy steel grub screws are widely used because they provide good strength and are cost-effective. Stainless steel is often preferable where moisture, washdown or corrosion resistance matters, although its strength and galling behaviour may differ from alloy steel.
Brass grub screws can be useful where avoiding damage to a softer shaft or component is more important than high clamping force. They are not a direct substitute for a hardened steel screw in a heavily loaded drive assembly. For critical applications, also check the manufacturer’s drawing, required standard, tightening torque and whether a threadlocking compound is specified.
A hardened cup point can provide strong retention, but it deliberately marks the shaft. On a shaft that will need regular repositioning, a flat point against a prepared flat may be the more serviceable arrangement. The correct choice depends on load, vibration, material hardness and how often the assembly is removed.
Write the full specification before purchasing
A usable grub screw description should state thread diameter, pitch where it is not standard, overall length, point type, drive, material and finish. For example: M8 x 16 mm, 1.25 pitch, cup point, internal hex, alloy steel black finish. If the point style is flat or dog point, state it clearly rather than assuming it from a product image.
For maintenance stores, label compartment stock by the complete specification. Mixing M6 x 10 cup point screws with M6 x 10 flat point screws may seem harmless until a repair requires a specific contact method. Keeping a sample board or thread gauge near the fastener store can reduce repeat identification work.
When dimensions are uncertain, avoid forcing a suspected replacement into the machine. A few careful measurements, a pitch check and a close look at the point type will usually identify the correct part faster than repairing a stripped thread. That practical approach keeps small fasteners from becoming a larger maintenance job.