What Causes Pallet Truck Sinking? 7 Checks

A pallet lorry that raises normally but slowly drops while parked is more than an inconvenience. It can leave a load unstable, delay picking work and point to a hydraulic fault that will worsen under regular use. When asking what causes pallet lorry sinking, the first job is to establish whether the forks are drifting down hydraulically or whether the lorry is physically sinking into a damaged or unsuitable floor. The symptoms, causes and repairs are different.

For most manual pallet lorries, forks that settle after lifting are caused by loss of hydraulic pressure. Electric pallet lorries can show similar symptoms, although their hydraulic power unit, control valve and electrical controls introduce additional possible faults. A methodical inspection helps avoid replacing parts that are still serviceable.

What causes pallet lorry sinking during a lift?

A manual pallet lorry holds its load through pressurised hydraulic oil. Pumping the handle operates a small pump, which sends oil into the lift cylinder. A check valve holds that oil in place, keeping the ram extended and the forks raised. If oil bypasses a seal or valve internally, pressure falls and the forks descend.

A very slow drop with a heavy load may be difficult to notice in a busy warehouse, but it should not be treated as normal wear. A sound pallet lorry should hold a correctly rated, balanced load at its raised position for a reasonable period without a visible loss of height. Rapid lowering, intermittent dropping or a lorry that will not remain raised at all requires attention before further use.

1. Worn or damaged hydraulic seals

The most common cause is wear in the pump or lift cylinder seals. Seals keep hydraulic oil where it is needed and prevent it passing around the piston. Over time, repeated pumping, dirt contamination, age and side loading can harden, cut or wear these components.

External oil around the hydraulic unit is a useful clue, but a pallet lorry can sink with no obvious leak. Internal seal failure allows oil to move past the piston inside the cylinder, so the pressure drops without oil reaching the floor. If the lorry lifts fully but drifts down when left alone, internal bypass is a strong possibility.

Seal replacement can be cost-effective on a quality lorry where the cylinder bore and piston rod remain in good condition. If there is deep corrosion, scoring or a bent rod, fitting fresh seals alone may only offer a short-term repair.

2. A leaking or contaminated lowering valve

The lowering valve releases hydraulic pressure when the handle control is moved to the lower position. If this valve does not fully seat when returned to neutral or lift, oil can leak back into the reservoir and the forks will creep down.

This can result from a worn valve seat, damaged O-ring, weak spring or debris in the hydraulic oil. Fine dirt is enough to prevent a precision valve from sealing correctly. Lorries used around loose packaging, swarf, dust or wet external loading areas are more exposed, particularly where maintenance is limited.

Before dismantling the hydraulic unit, check that the release chain, lever and control linkage are not holding the valve partly open. A badly adjusted chain can create the same symptom as a failed valve. The handle should move positively between lift, neutral and lower positions, with no binding or excessive free play.

3. Low, incorrect or degraded hydraulic oil

Low oil level can cause erratic lifting and poor holding performance, especially if air enters the system. Oil that is old, contaminated or unsuitable for the operating temperature can also affect valve operation and seal life.

Only use hydraulic oil specified for the pallet lorry model and follow the manufacturer’s filling procedure. Overfilling is not a solution and can cause other problems when the ram returns. If the oil looks milky, it may contain water; if it is unusually dark or contains visible particles, the system should be inspected and serviced rather than simply topped up.

After an oil change or repair, air may need bleeding from the hydraulic circuit. Air compresses under load, which can make lifting feel spongy and may contribute to inconsistent fork height. The correct process varies by model, but typically involves pumping the handle several times with the release control open, then retesting the lift function.

4. Worn pump piston, check valve or hydraulic ram

The pump assembly contains several parts that must work together: the pump piston, check valve, pressure valve, seals and ram. Wear in any of these can reduce the unit’s ability to maintain pressure.

A pallet lorry that needs excessive pumping, lifts only part way or drops faster with a heavier pallet may have more than a simple seal issue. Check-valve wear is particularly relevant where a lorry has been overloaded repeatedly. The valve may allow pressure to build briefly while pumping but fail to hold it once the handle stops moving.

Overloading also risks bending the ram or damaging the frame and linkage. The stated capacity applies to an evenly distributed load with the load centre in the correct position. A long pallet, unbalanced machinery component or load carried near the fork tips places greater stress on the hydraulic system than its weight alone might suggest.

5. Damage to the handle, chain or release linkage

The handle is not merely a steering component. On many hand pallet lorries, it operates a chain or rod connected to the lowering valve. If the chain is too tight, kinked, corroded or incorrectly adjusted after a repair, it may prevent the valve from closing fully.

Inspect the linkage with the lorry unloaded and on level ground. Look for bent parts, missing clips, stretched chain links and signs that the valve lever does not return cleanly. Do not shorten or tension the chain by guesswork. A small adjustment can materially change valve operation, so use the manufacturer’s procedure where available.

6. Fork, wheel and linkage problems mistaken for sinking

Not every loss of height is hydraulic. Worn load rollers, seized roller bearings, damaged fork-linkage pivots or a bent frame can cause the forks to sit unevenly or settle as a load is moved. The lorry may appear to be lowering when, in fact, one side is rolling poorly or a worn component is taking up clearance.

With the lorry unloaded, inspect both fork arms for equal height and check that the load rollers turn freely. Flat-spotted polyurethane wheels, cracked nylon rollers and loose pivot points affect travel and load stability. They can also increase the force needed to move a pallet, encouraging operators to pull at an angle and create further side loading.

If one fork drops or sits lower than the other, stop using the lorry for elevated pallet movement until the linkage and frame have been checked. An uneven pallet is a greater risk than a uniform, controlled descent.

7. The pallet lorry is sinking into the floor

Sometimes the phrase describes a different problem: the lorry is physically sinking or bogging down while travelling. This is common on soft asphalt, damaged concrete, timber decking, resin surfaces with failed sections, loose gravel or loading areas affected by heat and standing water.

Small load rollers concentrate substantial force into a limited contact area. Even a lorry within its rated capacity can mark or depress a weak floor, particularly with narrow wheels or a load left stationary for a period. Swivel steer wheels may also sink into joints, potholes and broken slab edges.

For this type of problem, inspect the travelling surface and the wheel material as well as the lorry. Nylon rollers generally offer low rolling resistance on smooth, hard floors, while polyurethane can provide quieter running and better floor protection. Neither will compensate for a floor that is not suitable for concentrated wheel loads. A larger-wheeled transport solution, floor repair or a revised handling route may be required.

A practical fault-finding sequence

Start with an unloaded visual inspection. Look for oil leaks, damaged forks, loose linkage parts, worn rollers and obvious frame damage. Then raise a known, safely balanced load within the lorry’s capacity and observe whether the forks fall while stationary. Note how quickly they descend and whether moving the handle control affects the rate.

Next, confirm that the lowering linkage fully returns to neutral and that the hydraulic oil is at the correct level and condition. If the external checks do not identify the fault, the hydraulic unit will usually need seal, valve or pump-component inspection. Keep the lorry out of service if it cannot hold a load safely. Blocking raised forks or relying on a temporary adjustment is not a repair.

Preventing repeat pallet lorry faults

Routine checks are cheaper than a failed pump unit during a busy shift. Keep load rollers and steer wheels clear of string, plastic wrap and debris. Wipe down the hydraulic area so new oil leaks are easier to spot, and avoid pressure-washing directly around seals and control linkages.

Match the lorry to the work as well. Capacity, fork length, wheel type, operating surface and pallet condition all matter. A standard hand pallet lorry is designed for level, hard warehouse floors and correctly supported pallets, not for dragging overloaded stock across broken yards or uneven thresholds.

If a pallet lorry begins to sink, record the symptom before ordering parts: whether it occurs loaded or unloaded, the approximate drop time, any oil loss and whether the lowering control feels normal. Those details make it far easier to identify the correct repair parts or decide when replacement is the more economical option.