A loose thread in thin sheet metal can turn a straightforward repair into repeat work. Rivet nuts, also called rivnuts or threaded inserts, provide a strong reusable thread where there is no access to the rear of the panel. Knowing how to install rivet nuts correctly means selecting the right insert, drilling the hole accurately and setting the tool without damaging the parent material.
They are widely used in fabrication, vehicle bodies, machinery guards, cabinets, racking accessories and maintenance work. Once fitted correctly, a rivet nut allows a bolt or machine screw to be removed and refitted without relying on a self-tapper in thin material.
Choose the rivet nut before drilling
The insert must suit both the material thickness and the application. A rivet nut works by collapsing on the blind side of the sheet as the mandrel pulls against its flange. The collapsed section clamps the sheet between the flange and the formed bulge. If the grip range is wrong, the insert may spin, sit loose or distort the panel.
Start with the thread size required by the component being fixed. M4, M5, M6 and M8 are common metric sizes in workshop and industrial applications. Then check the manufacturer's stated grip range against the combined thickness of the material being clamped. This includes paint, coatings, washers or overlapping sheets where relevant.
Material choice matters as well. Aluminium rivet nuts are useful for lighter-duty work and corrosion resistance, but are not the best choice for high tightening loads. Steel inserts offer greater strength for general fabrication. Stainless steel suits exposed or corrosive environments, although it needs more pulling force and a capable setting tool.
The body style also affects performance. Round-body inserts are common and economical, but rely on a correctly sized round hole and adequate clamp load to prevent rotation. Splined or serrated bodies give more resistance to turning in softer sheet. Hex-body rivet nuts provide the highest anti-rotation resistance when installed in a properly punched or drilled hexagonal hole, but preparation takes more time.
Tools needed to install rivet nuts
For occasional M4 to M6 jobs in accessible sheet steel, a hand rivet nut tool is normally sufficient. Lever tools provide greater mechanical advantage and are better suited to repeated work or larger inserts. Pneumatic and battery-powered tools are practical where production volume, stainless inserts or larger thread sizes make manual setting slow and inconsistent.
You will also need a drill or pillar drill, suitable drill bits, a centre punch, marking equipment, a deburring tool and the correct mandrel and nosepiece for the insert. Use a thread gauge or a known bolt to confirm the insert thread if sizes have been mixed in storage.
Do not try to set a rivet nut with an ordinary pop-rivet gun unless it is specifically designed for threaded inserts. The pulling stroke, mandrel arrangement and load requirements are different. Improvised methods using a bolt, nut and spanner can work in an emergency, but they are slow and make it easier to overtighten, damage threads or leave an inconsistent set.
How to install rivet nuts step by step
Mark and prepare the fixing position
Measure and mark the hole position carefully. Check for obstructions behind the panel, including wiring, hydraulic lines, moving parts and structural members. On a machine guard or vehicle panel, poor hole placement can create more problems than the missing thread it was intended to solve.
Centre-punch the mark to stop the drill wandering. Support thin sheet where possible. If the workpiece is already bent or formed, make sure the rivet nut flange will sit on a flat, clean surface rather than bridging a radius or weld seam.
Drill the correct hole size
The hole diameter must match the insert specification, not simply the bolt thread size. For example, an M6 rivet nut does not fit a 6 mm hole. Its outside body diameter is larger, and the required hole size varies by insert material and body design.
Drill a pilot hole first if accuracy is important, then open it to the specified diameter. A pillar drill gives the best control on loose parts, while a hand drill is often necessary for installed equipment and panels. Keep the drill square to the surface so the insert flange seats evenly.
Deburr both sides of the hole. A burr under the flange prevents proper seating and can leave a gap that encourages the insert to move under load. Remove swarf from the work area, particularly around machinery, electrical enclosures and moving equipment.
Fit the insert to the setting tool
Install the correct threaded mandrel and nosepiece in the rivet nut tool. Thread the rivet nut fully onto the mandrel by hand. The insert should sit against the nosepiece without cross-threading.
Place the rivet nut into the prepared hole. Hold the tool at 90 degrees to the workpiece. If the tool is angled, the insert may collapse unevenly, leaving the flange proud on one side and reducing grip strength.
Set the rivet nut with controlled force
Operate the tool steadily until the insert collapses on the blind side and grips the sheet. With adjustable tools, begin with the recommended setting for the insert size and material. It may need a small adjustment after testing on scrap of the same thickness.
Do not keep pulling once the insert has fully formed. Excess force can strip the internal thread, deform thin sheet, crack coatings or cause the insert body to buckle. The aim is a firm clamp, not maximum tool force.
Release the tool and unscrew the mandrel. Inspect the flange. It should sit flat against the surface with no visible gap, rocking or damage. Fit a matching bolt by hand for several turns. It should engage smoothly without resistance caused by damaged threads.
Check the installation before loading it
A correctly installed rivet nut should not rotate when the fixing bolt is tightened to the appropriate torque. It should also remain secure when the bolt is removed and refitted. For critical repairs or repeated installations, test one insert in a sample piece first.
Pay attention to the load direction. Rivet nuts are useful for clamping components to sheet material, but the parent sheet still determines overall joint strength. A thin aluminium panel may hold an M6 thread securely yet still flex or tear if used to support heavy equipment. Increase panel thickness, add a backing plate or use a different fastening method where loads are high or subject to vibration.
Use sensible tightening torque. The bolt can be stronger than the insert or the sheet it is fitted into. Over-tightening is a common cause of spinning inserts, especially in thin aluminium or oversized holes.
Common rivet nut installation faults
If a rivet nut spins in the hole, the hole may be oversized, the grip range may be unsuitable or the insert may not have been set tightly enough. Remove it where possible and fit a new, larger-body insert or change to a splined or hex-body type. Reusing a spinning insert is not reliable.
If the flange does not sit flush, look for burrs, paint build-up, a distorted panel or an angled tool. Clean and correct the surface before fitting another insert. Trying to pull a badly seated insert down with the fixing bolt can damage the component and leave the joint weak.
If the internal thread strips during installation, the tool may have been over-set or the wrong mandrel may have been used. Replace the insert and check the tool adjustment. Do not force a bolt into damaged threads, particularly where later removal is required for servicing.
Where corrosion is a concern, consider the compatibility of the insert, parent material and fixing bolt. Stainless steel against aluminium can create corrosion issues in wet or outdoor conditions. Suitable coatings, isolating washers or matched materials can reduce the risk, depending on the environment.
For maintenance teams and fabricators, rivet nuts are a practical way to create serviceable threaded fixings without welding or rear access. Take the extra minute to confirm the grip range, hole size and setting tool before pulling the first insert - it is usually quicker than rectifying a loose thread in a finished panel.