Grub Screw Point Types Guide for Secure Fixing

A grub screw may be small, but the wrong point type can mark a shaft, loosen under vibration or make a component difficult to remove during maintenance. This grub screw point types guide explains what each point is designed to do, where it is normally used and what to check before fitting one in a workshop or industrial assembly.

Grub screws, also called set screws, are headless fasteners threaded fully along their length. They are commonly used to secure pulleys, gears, collars, handles, knobs and couplings to a shaft. Their holding performance depends on more than thread size and material grade. The point profile determines how the screw contacts the mating part, so it has a direct effect on grip, positioning and surface damage.

Grub screw point types guide: choosing the contact profile

The practical question is whether the screw needs to bite into the shaft, sit against a flat, locate in a recess or resist movement without damaging a finished surface. There is no single best point type. A cone point can provide high holding power, for example, but it may be unsuitable where the shaft must remain reusable.

Cup point grub screws

Cup point grub screws are among the most common types used in general engineering and maintenance work. The end has a shallow concave form with a sharp outer rim. As the screw is tightened, that rim bites into the shaft or component surface.

This makes the cup point a strong general-purpose choice for securing collars, hubs and pulleys where minor marking is acceptable. It offers good resistance to vibration and is particularly useful on softer steels, aluminium and similar materials where the point can gain purchase.

The trade-off is surface damage. A cup point often raises a burr or leaves an indentation, which can make later removal of a hub or collar more difficult. It is not normally the first choice for polished shafts, precision ground surfaces or components that will be repositioned regularly.

Cone point grub screws

A cone point has a sharp, tapered tip intended to locate positively in a prepared hole, dimple or groove. It gives accurate positioning and strong resistance to sideways movement when used with a matching recess.

This point type is often chosen for more permanent assemblies, indexing applications and parts requiring repeatable location. A cone point can also be used directly against a shaft, but it concentrates load in a very small area and can cause significant damage. For that reason, a drilled location point is usually preferable where accuracy matters.

When specifying a cone point screw, check that the mating component has enough wall thickness around the locating hole. A shallow or poorly positioned dimple may deform, reducing holding strength and affecting alignment.

Flat point grub screws

Flat point grub screws have a flat bearing end that presses against the mating surface without deliberately cutting into it. They are suitable where the component needs to be adjusted, removed or reused without marking the shaft unnecessarily.

They are commonly used against a machined flat on a shaft, often called a D-flat, or against softer materials where a cutting point would cause excessive damage. A flat point spreads its force over a wider contact area than a cone or cup point, reducing local deformation.

Holding power is generally lower than a cup or cone point on a plain round shaft. If the assembly is subject to high torque, shock loading or continuous vibration, a flat point should ideally bear on a properly machined flat rather than a curved surface. This gives a more stable seat and prevents the screw from slipping as it is tightened.

Dog point grub screws

Dog point grub screws have a reduced-diameter cylindrical projection at the end. Rather than gripping by digging into a surface, the dog enters a pre-drilled hole, slot or groove to locate parts accurately.

This makes them useful for shaft collars, sliding mechanisms, adjustment stops, fixture work and assemblies that need positive location. The dog point can also allow a component to move along a controlled path when it engages with a slot.

The important measurement is the dog diameter and length, not only the thread size. The mating hole must suit the dog closely enough to control movement but still allow assembly without forcing or binding. A dog point is generally a locating solution first and a clamping solution second, so consider whether an additional fastener or clamping method is needed for high-load applications.

Knurled cup point grub screws

Knurled cup point screws are designed for maximum grip. Their point combines a cup-shaped contact face with serrations or knurling that bite aggressively into the mating material.

They are useful where vibration is severe or where a standard cup point does not provide sufficient resistance to loosening. Typical uses include heavy-duty machine assemblies, shafts that experience repeated movement and components where a permanent or near-permanent fixing is acceptable.

The downside is clear: knurled points cause more damage than standard cup points. They can produce deep marks and make disassembly difficult, particularly on softer shafts. They should not be selected where preserving the shaft finish or allowing regular adjustment is a priority.

Oval point grub screws

Oval point screws have a rounded, domed contact end. The profile provides a middle ground between the non-marking nature of a flat point and the concentrated contact of a cone point.

They are suitable for applications requiring moderate holding force with less surface damage than a cup or cone point. The rounded end can be useful where adjustment is needed, or where the mating surface is curved and a sharp point would be unsuitable.

An oval point is not normally the preferred option for maximum torque transmission. Use it where controlled pressure and reduced marking are more valuable than aggressive grip.

Match the point type to the shaft and application

The shaft material, finish and operating conditions should drive the choice. A standard mild steel shaft in a pulley assembly may suit a cup point grub screw well. A hardened, ground shaft may need a flat point against a prepared flat, or a dog point engaging with a drilled location feature.

For aluminium, brass and engineering plastics, avoid assuming that a sharper point gives a better result. A cone or knurled cup point can distort softer materials, reduce alignment and weaken the component over repeated assembly. A flat point with a suitable bearing area is often more controlled, although thread engagement in the receiving part also needs careful consideration.

Vibration changes the decision. Where machinery movement is likely to loosen a fixing, use a point type that has a positive mechanical engagement, such as a cup, cone or dog point, provided the mating component is suitable. Threadlocking compound may also be appropriate, but it should support correct point selection rather than compensate for an unsuitable screw.

Check thread size, material and drive type

Point type is only one part of the specification. Confirm the thread diameter, pitch, overall length, material and drive before ordering. Metric grub screws are commonly available in steel, stainless steel and alloy steel, with hex socket drives being widely used for reliable tightening in confined spaces.

Steel grub screws are suitable for many general workshop and engineering applications, while stainless steel offers better corrosion resistance for damp or externally exposed locations. Stainless grades can have lower strength than high-tensile alloy steel, so do not select solely on corrosion resistance where high clamping loads are involved.

Length matters because the screw should provide sufficient thread engagement without bottoming out or protruding where it could create a safety issue. In blind threaded holes, allow clearance at the bottom so the point contacts the mating part before the screw runs out of thread.

Installation details that prevent loosening

Clean both the threaded hole and the mating surface before assembly. Oil, swarf, old threadlock and paint can alter tightening feel and reduce the quality of the contact. If a cone or dog point is intended to locate in a drilled feature, ensure that feature is correctly positioned before final tightening.

Tighten with a correctly sized hex key or driver. An undersized or worn tool can round the socket, particularly on smaller grub screws. Apply torque appropriate to the thread size, material and assembly requirements. Excessive tightening can strip threads in aluminium or damage a shaft without delivering a more reliable joint.

For components that need regular servicing, record the point type used and inspect the shaft during removal. Repeated use of a cup or cone point in slightly different positions can create a series of marks that affect fit and run-out.

The most dependable fixing is usually the one designed around the component from the start: use a prepared flat for a flat point, a location hole for a cone or dog point, and a biting cup point only where the resulting mark is acceptable. That small decision can prevent a loose hub, damaged shaft or avoidable maintenance delay later.