A pallet lorry that will not lift to full height, feels spongy at the handle or slowly drops under a load often has air in its hydraulic circuit. Knowing how to bleed a pallet jack can restore normal lifting where the fault is simply trapped air or an incorrect oil level. It is a straightforward maintenance task on many manual pallet lorries, but only if the lorry is empty, stable and the underlying fault has been identified correctly.
Hydraulic equipment stores energy. Keep hands and feet clear of the forks and linkage throughout the process, do not work beneath raised forks, and never attempt a repair with a pallet load still in place.
When bleeding a pallet jack is the right fix
Bleeding removes air from the pump and hydraulic system. Air can enter after the oil reservoir has been opened, following transport with the lorry on its side, after a hydraulic repair, or where a low oil level has allowed the pump to draw air. Unlike hydraulic oil, air compresses. The result is a handle that pumps without producing a firm, consistent lift.
Typical signs include forks that lift slowly or only part-way, a pump action that feels unusually light, or lifting that improves briefly after repeated pumping. A lorry may also fail to rise after it has been stored for a long period.
However, bleeding will not cure every lifting problem. If oil is visibly leaking from the ram, pump body, valve assembly or hose on an electric model, the system needs repair before it is bled and refilled. Worn seals, a damaged piston, a bent push rod, seized linkage or an incorrectly adjusted release valve can produce similar symptoms. Treat bleeding as a first maintenance check, not a substitute for replacing failed parts.
Prepare the pallet lorry and check the basics
Park the pallet lorry on level, firm ground with no load on the forks. Lower the forks completely using the control lever. This position reduces pressure in the hydraulic cylinder and gives the most reliable indication of the oil level.
Clean the pump unit before opening anything. Dirt entering through the filler point can damage the pump, seals and control valve. Have clean rags ready, along with the correct hydraulic oil, a suitable screwdriver or spanner for the filler plug where required, and a small container in case excess oil needs removing.
Most manual pallet lorries use mineral hydraulic oil, commonly ISO VG 32, but the specified grade depends on the manufacturer and operating environment. Check the lorry's manual or existing product specification before topping up. Do not use engine oil, brake fluid or mixed, unknown oil. These can attack seals or cause poor operation, particularly in cold warehouse conditions.
Before opening the reservoir, inspect the control chain or rod between the handle and release valve. The lever should move freely between lift, neutral and lower positions. If it is held partially in the lower position, the release valve stays open and the lorry cannot build pressure, regardless of how much pumping is done.
How to bleed a pallet jack safely
The precise filler arrangement varies by make. Many manual pallet trucks have a small oil filler screw or rubber bung on the hydraulic pump body. Some are accessed near the base of the handle. Use the manufacturer's instructions where available rather than forcing a plug or altering valve settings unnecessarily.
Release trapped pressure first
With the forks fully down and no load present, set the handle control to the lower position. Pump the handle repeatedly, normally 10 to 15 full strokes. This action cycles the pump while the release valve is open and can purge a small amount of trapped air without removing the filler plug.
Then return the lever to the neutral or lift position, depending on the truck's control arrangement, and pump the handle several times. Test whether the forks now rise smoothly. For a lorry that has only drawn in a small amount of air, this simple procedure is often sufficient.
Check and top up the hydraulic oil
If the lorry still feels soft or does not lift, remove the filler plug carefully with the forks remaining fully lowered. Check the oil level against the manufacturer's stated fill point. Do not fill the reservoir to the top unless the specification specifically says to do so. Hydraulic oil expands and the displaced volume changes as the ram operates, so overfilling can cause leakage or poor performance.
Add only small amounts of clean, correct-grade oil. A narrow clean funnel helps prevent spills and contamination. If the oil is milky, heavily darkened, smells burnt or contains visible particles, topping up alone is not the right repair. The system should be inspected and the oil changed as part of a proper service.
Refit the filler plug securely, wiping away any spilled oil. Oil on the floor creates a slip risk and makes future leaks harder to spot.
Cycle the pump to purge the air
Set the handle to the lower position again and pump it 10 to 15 times. Move the control to lift and pump until the forks reach their normal maximum height. Lower the forks and repeat this full cycle two or three times.
During the final lift, the forks should rise evenly and the handle should develop a firm, predictable resistance. Do not hold the handle at the end of its travel or continue forcing it once the forks have reached maximum height. Repeated over-pumping adds unnecessary stress to the pump assembly.
Test before returning the lorry to service
Raise the empty forks to a moderate height and leave them for several minutes. They should not drift down noticeably. Next, test with a suitably light, stable load in a clear area before using the lorry at its rated capacity.
A successful bleed produces a normal lift, but it does not prove that the lorry is safe if there is leakage, damaged wheels, a cracked frame or faulty steering. Include a general pre-use inspection before putting it back into regular warehouse service.
If the pallet lorry still will not lift
If bleeding and correcting the oil level make no difference, stop pumping and inspect the likely mechanical or hydraulic causes. Continuing to operate a faulty unit can turn a minor seal or linkage issue into a larger repair.
- External oil leak: Wetness around the ram, pump body or valve points to worn seals, damaged fittings or a cracked component.
- Release valve not closing: A loose, stretched or badly adjusted control chain can prevent the valve from seating fully.
- Internal seal failure: Forks that rise but drift down, particularly under load, may have bypassing seals inside the pump or cylinder.
- Damaged pump or linkage: A bent handle pin, seized pivot, broken spring or worn pump piston can prevent pressure building.
Oil condition, storage and planned maintenance
A manual pallet lorry does not need its oil checked every day, but it should form part of planned maintenance, especially in high-use warehouses. Check for leaks, smooth lifting and controlled lowering during routine inspections. A lorry used across rough yards, cold stores or dusty workshops may require more frequent attention than one used on clean, level warehouse floors.
Store pallet lorries with forks lowered. This reduces trip hazards, protects the ram from unnecessary exposure and avoids leaving a raised mechanism under pressure. Avoid leaving equipment outdoors where water, grit and corrosion can affect the pump, wheels and handle linkage.
When replacement parts are required, match them to the lorry model and dimensions. Seal kits, pump units, steer wheels, fork rollers and control components are not universally interchangeable, even where pallet lorries look similar.
A pallet jack that lifts cleanly, lowers under control and holds its load is safer and faster to use. Bleed the hydraulic system carefully, use the correct oil, and investigate any recurring loss of lift before it disrupts a shift.