A tap will not compensate for the wrong pilot hole. Drill undersize and torque rises sharply, risking a snapped tap or distorted thread. Drill oversize and the fastener may fit, but thread engagement and pull-out strength fall away. Choosing the best tapping drill sizes is therefore a basic but critical workshop decision.
For general engineering work, the correct size depends on the thread standard, nominal diameter, pitch or threads per inch, material and required percentage of thread engagement. A sensible drill chart gets the job moving, but it should not replace checking the drawing, fastener specification and tap manufacturer's guidance where the job is safety-critical or tightly toleranced.
Best tapping drill sizes for common metric threads
The metric coarse series is the usual starting point for workshop repairs, fixtures, machinery guards and general fabrication. Coarse threads are more tolerant in everyday use, quicker to assemble and less vulnerable to damage than fine threads in softer materials.
| Metric thread | Standard pitch | Tapping drill size |
|---|---:|---:|
| M3 x 0.5 | 0.5 mm | 2.5 mm |
| M4 x 0.7 | 0.7 mm | 3.3 mm |
| M5 x 0.8 | 0.8 mm | 4.2 mm |
| M6 x 1.0 | 1.0 mm | 5.0 mm |
| M8 x 1.25 | 1.25 mm | 6.8 mm |
| M10 x 1.5 | 1.5 mm | 8.5 mm |
| M12 x 1.75 | 1.75 mm | 10.2 mm |
| M14 x 2.0 | 2.0 mm | 12.0 mm |
| M16 x 2.0 | 2.0 mm | 14.0 mm |
These sizes are the familiar workshop recommendations for standard cutting taps and approximately 70-75% thread engagement. That level is normally more than adequate for a sound fastening in steel, stainless steel, aluminium and engineering plastics, provided the engagement depth is suitable.
A useful metric rule is simple: subtract the thread pitch from the nominal diameter. An M10 x 1.5 thread, for example, needs a drill close to 10 mm minus 1.5 mm, giving 8.5 mm. This calculation is useful when working away from a chart, but use a published recommendation for fine-pitch, specialist or tolerance-controlled work.
Fine metric threads need separate checks
Do not use the coarse-thread drill simply because the nominal diameter is the same. An M8 x 1.0 fine thread requires a 7.0 mm tapping drill, rather than 6.8 mm for M8 x 1.25. Similarly, M10 x 1.25 normally uses 8.8 mm rather than 8.5 mm.
Fine threads can be useful where adjustment is needed, wall thickness is limited or a greater tensile area is required. They are less forgiving of damage, contamination and cross-threading, particularly in maintenance environments. Confirm the pitch before drilling rather than relying on the bolt diameter stamped on a drawing or quoted over the phone.
Tapping drill sizes for UNC and UNF threads
Imperial fasteners remain common on older machinery, imported equipment and some specialist assemblies. UNC is the coarse Unified National thread, while UNF is the finer series. The designation includes diameter and threads per inch, so 1/4-20 UNC and 1/4-28 UNF are not interchangeable.
| Thread | Tapping drill size | Nearest metric drill |
|---|---:|---:|
| No. 4-40 UNC | No. 43, 2.26 mm | 2.3 mm |
| No. 6-32 UNC | No. 36, 2.70 mm | 2.7 mm |
| No. 8-32 UNC | No. 29, 3.45 mm | 3.5 mm |
| No. 10-24 UNC | No. 25, 3.80 mm | 3.8 mm |
| 1/4-20 UNC | No. 7, 5.10 mm | 5.1 mm |
| 5/16-18 UNC | Letter F, 6.53 mm | 6.5 mm |
| 3/8-16 UNC | 5/16 in, 7.94 mm | 7.9 mm |
| 1/2-13 UNC | 27/64 in, 10.72 mm | 10.7 mm |
For common UNF threads, 1/4-28 generally uses a 5.4 mm drill, 5/16-24 uses 6.9 mm, 3/8-24 uses 8.3 mm, and 1/2-20 uses 11.5 mm. These are practical nominal equivalents, but a numbered, lettered or fractional drill may be the stated size on an imperial drawing.
The imperial calculation follows the same principle. Subtract one thread pitch from the major diameter, with pitch expressed as 1 divided by TPI. For 1/4-20 UNC, the pitch is 0.050 in. Subtracting that from 0.250 in gives a drill size of approximately 0.200 in, close to a No. 7 drill at 0.201 in.
Why the recommended drill size can vary
A tapping drill chart is a starting point, not a universal instruction. Charts may specify different drills for 60%, 65%, 75% or higher thread engagement. The practical difference matters most in difficult materials and small thread sizes.
Higher thread percentage means more material is cut from the hole. It can marginally increase thread contact, but it also increases tapping torque. In stainless steel, high-tensile steel and blind holes, forcing a high-percentage thread is often a poor trade. The tap can seize, work-harden the material or break below the surface, turning a short job into a costly extraction exercise.
For general fasteners, 65-75% engagement is widely used because it gives reliable holding strength without excessive torque. Once several threads are fully engaged, extra thread height offers diminishing returns. If more strength is required, increasing engagement length, using a larger fastener, fitting an insert, or changing the joint design is often more effective than drilling undersize.
Softer materials need judgement too. Aluminium and brass tap readily, but thin sections can strip if the thread depth is insufficient. Nylon, acetal and other engineering plastics may benefit from a slightly different approach because material behaviour, creep and thread-forming method affect the result. Test a representative offcut when the component is expensive or the fit is critical.
Drill, tap and hole preparation matter as much as size
Use a sharp, correctly sized drill and keep it square to the workpiece. A wandering or oversized hole will not produce a dependable thread, even if the number marked on the drill is correct. For a tapped hole that must locate another part accurately, spot drill first and use a rigid drill press, milling machine or suitable guided arrangement where possible.
Deburr the entry with a light countersink or chamfer. This helps the taper lead of the tap enter cleanly, reduces the risk of raised material around the hole and gives the first thread a better start. Do not add an excessive chamfer in thin material, as it removes useful thread engagement.
Blind holes require extra planning. Drill deeper than the required full thread length to allow for the tap lead and chips. A taper tap cannot form full threads close to the bottom; a second or plug tap gets closer, and a bottoming tap is used for maximum depth after the thread has been started. Never bottom the tap by force.
Apply an appropriate cutting fluid, especially when tapping steel or stainless steel. Turn the tap steadily, keep it aligned and break chips regularly when hand tapping. For machine tapping, use the correct tapping cycle, lubricant and feed synchronisation. Reversing, stopping or forcing a tap unnecessarily can damage both the tool and the thread.
Check the finished thread before fitting the assembly
A bolt should enter by hand for the first few turns without binding. If it feels tight immediately, stop and inspect the thread, pitch and hole condition rather than forcing the fastener with a spanner. For repeat production, a go/no-go gauge is the dependable method for confirming internal thread size and pitch.
Keep metric, UNC, UNF, BSP and other thread systems clearly separated in workshop storage. Similar diameters can look convincing at a glance, but a mismatched fastener can damage a newly tapped hole before the error is noticed. Mark drill sets and tap cases clearly, and retain a drill chart close to the bench.
For day-to-day maintenance and fabrication, a set of sharp fractional, metric, number and letter drills alongside quality taps covers most requirements. Select the specified drill, prepare the hole properly and let the tap cut at a controlled rate. That approach protects tools, avoids downtime and produces threads that hold when the equipment goes back into service.